Search
Login
Recommended
How to insulate a garage door with your own hands, how can you insulate a garage door
A car is not a luxury, but a means of transportation, that is how we feel it in the 21st century. Since the advent of our car, a new problem arises of its storage. The garage solves this problem as best as possible, at the same time it can serve as a small workshop in which you can craft a variety of crafts. In winter, to improve the microclimate in the garage, it is necessary to install a heating and ventilation system, to reduce heat loss, it is necessary to insulate. And so, we warm the garage door.
Table of contents
According to sanitary norms and rules (SNiP 21-02-99 Car Parking), for the proper and long-term storage of the car in the garage, the room temperature + 5C is necessary.
In heated parking lots, the calculated air temperature in the premises for car storage should be taken 5 C
Garage swing gate insulation
If your garage box is located in a garage cooperative, then the insulation of the garage can be minimized by warming only the gate. At the same time, if the gates are not insulated, then heat losses through the metal will be maximum.
Gate insulation is required. The choice is up to the material.
Experience has shown that when gluing polystyrene onto the gate metal, moisture condenses between the metal and the polystyrene. Condensation will cause corrosion of the metal and accordingly reduce the service life of the garage door. Therefore, to isolate the door metal from the main insulation, we use waterproofing. This can be a self-adhesive isolon. The isolon layer, depending on the thickness, serves as the main or additional thermal insulation.
If the thickness of the isolon is not sufficient, we glue sheets of polystyrene foam or other foam on it. For gluing, you can use mounting foam or tile adhesive.
Under the foam sheets you can make an additional crate, but you can also use the corner of the gate itself. At the corners, kerchiefs should be welded, the polystyrene under these kerchiefs is cut and stuffed inside under the scarf. And for better sealing we use polyurethane foam. When working, pre-arrange the foam sheets, this will reduce the amount of waste. Seams, depending on the glue used, must be foamed or necessarily glued.
When using extruded polystyrene foam, the external finish can be minimized by gluing the seams with aluminum foil. This material has increased rigidity and will last a long time without problems.
When using foamed polystyrene foam of low density, it is necessary to cover the material. You can use siding, OSB or wood lining for this.
As a heater, you can use polyurethane foam. Foamed sprayed polyurethane foam will insulate the gate in seconds. Good adhesion (at the level of 2 kg / cm2) to most materials allows its use in any conditions. The manufacturer company guarantees reliable operation of the insulation up to 10 years. In this case, the operation lines can be up to 50 years. To increase the service life and good appearance of PPU, it is necessary to protect it with an additional layer.
Sectional doors insulated
Sectional doors are designed to avoid many problems of swing gates. Winter cold confronts the owner of the swing gates with the first problem of how to get into the garage, because the gates are covered with snow. Sectional doors have no such problem. The second problem of swing gates is the opening radius of such gates. Indeed, in many places there is simply physically not enough space for the gate to open completely. It is also necessary to ensure that with the gate open, the sash is securely fastened. After all, even a small gust of wind can turn the sash and damage the car.
Sectional doors are hidden under the ceiling of the garage and do not cause any problems.
Sectional doors are made of modern durable materials, they do not require insulation, since the insulation is already installed. As a heater, foamed polyurethane is mainly used. This sandwich panel reliably protects the gates and the garage from the cold.
Most door models are also equipped with electric hoists, which increases the comfort of use for the garage owner. Such a gate has a function that, when the power is cut off, the gate can be lifted manually.
Consider the arrangement of sectional doors.
- rack and vertical guide;
- horizontal guide;
- sections of the door leaf;
- seal with seal;
- spring;
- intermediate loop;
- torsion shaft;
- suspension;
- electric motor;
- roller bracket;
- cable pulley;
- bracket;
- intermediate bracket;
- bottom bracket;
- cable drum;
- unlocking the electric motor outside the room;
- jumper;
- crossbar lock;
- seal.
The appearance of the gate can be easily adjusted to the facade. Large color gamut, various textures allow the customer to choose what he needs. There is an opportunity to choose a material for wood, though this will increase the cost of construction.
If the gates in the drywall are not yet installed, and only their choice is being made, then modern sectional gates are the gates of the next decade.
If you have swing gates installed, insulate them correctly, this will extend the life of the garage door and car. Successes.